GE Dishwasher Error Codes

GE Dishwasher Error Codes: A Comprehensive Guide

Understanding error codes in GE dishwashers is crucial for effective troubleshooting. These codes serve as indicators of specific issues, enabling users to identify and resolve problems quickly. In this article, we will explore all possible error codes for GE dishwashers, their meanings, causes, and possible fixes, making this your one-stop solution for any GE dishwasher-related concerns.

Understanding Error Codes

Error codes in GE dishwashers help diagnose operational issues and malfunctions. When an error occurs, the dishwasher displays a specific code, allowing users to refer to the manual or this guide for troubleshooting steps. Knowing how to access and interpret these error codes can save time and prevent further damage to the appliance.

List of GE Dishwasher Error Codes

1H

• Meaning: The dishwasher is in Delay Start mode.
• Cause: The user has set a delay for the start of the wash cycle.
• Possible Fix: Wait for the countdown to finish or cancel the Delay Start option in the settings.

C1

• Meaning: The pump out during drain has exceeded 2 minutes.
• Cause: This could be due to a clogged drain or air gap issues.
• Possible Fix: Clean the air gap, reposition the hose, or run the disposer to clear any blockages.

C2

• Meaning: The total pump-out cycle exceeds 7 minutes.
• Cause: Persistent drainage issues, possibly due to clogs.
• Possible Fix: Press RESET to stop the beep and inspect the drainage system for any blockages.

C3

• Meaning: The dishwasher will not drain.
• Cause: There may be a blockage in the drain or a malfunctioning pump.
• Possible Fix: Disconnect power for about 30 seconds and reset the dishwasher; check for clogs in the drain.

C4

• Meaning: Machine filled twice after a power failure.
• Cause: A stuck or failed float switch could lead to this error.
• Possible Fix: Touch start and then cancel/reset the machine; check the float cover for debris and ensure it’s functioning properly.

C5

• Meaning: The pump-out time is too short.
• Cause: This could occur if the water supply is turned off or the float is stuck.
• Possible Fix: Ensure that the water supply is on and try tapping the float cover to unstick it.

C6

• Meaning: Water temperature is too low.
• Cause: The incoming water temperature is below the required 120°F.
• Possible Fix: Run hot water in the faucet adjacent to the dishwasher before starting it or adjust the water heater temperature.

C7

• Meaning: The dishwasher’s water temperature sensor circuit has become inoperative.
• Cause: This could be due to a faulty sensor or wiring issue.
• Possible Fix: Disconnect power for 30 seconds and reset the dishwasher; check the sensor for functionality.

C8

• Meaning: The detergent cup is blocked from opening fully.
• Cause: An obstruction may be preventing the cup from opening completely.
• Possible Fix: Remove any obstructions (e.g., silverware or pans) and ensure the detergent cup closes properly.

PF Code

• Meaning: Indicates a power failure to the dishwasher.
• Cause: There has been a loss of power during operation.
• Possible Fix: Select the desired cycle and press Start to resume normal operation.

Cup Open

• Meaning: The detergent cup has not been closed.
• Cause: This is a reminder to add detergent and latch the cup closed.
• Possible Fix: Close and latch the cup; if necessary, press Start to override this error.

FTD or F56

• Meaning: Failure to drain.
• Cause: The dishwasher did not drain properly due to blockages.
• Possible Fix: Inspect the drain hose, air gap, and disposer for any obstructions.

LEAK DETECTED

• Meaning: Possible leak is detected.
• Cause: Water leakage during the wash cycle.
• Possible Fix: The cycle will be canceled; check for leaks and contact service if necessary.

999

• Meaning: Possible leak detected on models with “Floor Protect with Alert.”
• Cause: The leak detection feature has been activated.
• Possible Fix: Contact service for diagnosis and repairs if this error occurs.

H2O

• Meaning: Indicates a low water situation.
• Cause: This may happen if the water inlet hose is kinked or there is a low water supply.
• Possible Fix: Check the inlet water hose for kinks and ensure the water supply is adequate.

PrS

• Meaning: Pressure switch failure.
• Cause: A malfunctioning pressure switch can lead to this error.
• Possible Fix: Inspect the pressure switch for functionality; consider contacting a technician if issues persist.

Troubleshooting Tips

If you encounter any of these error codes, follow these general troubleshooting steps:

• Consult the User Manual: Check the manual specific to your GE dishwasher model for further guidance on the error codes.
• Inspect for Blockages: Regularly check and clean filters, air gaps, and drain hoses to prevent clogs.
• Reset the Dishwasher: If multiple error codes appear, resetting the dishwasher by disconnecting power for 30 seconds may help resolve the issue.
• Seek Professional Help: If the problem persists despite troubleshooting, contact a professional technician for assistance.

Conclusion

Understanding the error codes of your GE dishwasher is essential for effective troubleshooting and maintenance. By referring to this comprehensive guide, you can quickly identify and resolve issues, ensuring your appliance runs smoothly. Regular maintenance and timely interventions can help prevent future errors and extend the lifespan of your dishwasher.